Maintenance Sign-Up

 

What are your thoughts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately difficult project. If the old tub is readily obtainable, the task can move rapidly; if you have to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and also set in the new one. Ensure you have qualified yourself for the task as well as are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed job, it is much better to think about employing one before you start. Possibilities are you might require a professional plumber to make tube connections.
This short article will assist you set up a new tub in your shower room if you have currently purchased a new tub as well as don't require to transform the setup of your previous water pipelines.
Your tools and product checklist ought to consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Getting ready for the Setup

To start with, the sustaining frame supplied with the bath ought to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installment, then the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be rather problematic because of the limited gain access to that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the remaining water that will come from the pipes. When the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Before carrying on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

 

 

Mounting the Tub

Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to guarantee that the tub is leveled all round. This can be attained by examining the level and readjusting the feet on the bathtub up until the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost versatile faucet port to the proper supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also inspect all joints and also brand-new pipework for leaks and tighten them if needed. Load the bathtub and additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it right into its final placement.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, after that you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the tap and also the sink. Secure the tap in place with the producer offered backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bathtub

In the location where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and also the tiling, causing issues with wetness and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to permit the activity experienced when the tub is in use. The sealer can break relatively very early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently readily available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I came across that blog entry on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. Do you know about somebody who is fascinated with Installing A Bathtub? Please feel free to promote it. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.

Tap leaks? Inform.